潮流能水平轴水轮机在剪切来流下的水动力分析

采用基于计算流体力学方法的全尺度数值模拟计算,建立了适用于潮流能水轮机模拟的剪切来流环境,通过数值计算结果,对潮流能水轮机随时间变化的宏观力和流场特征进行了系统分析,探索水轮机在复杂工况下的水动力特性规律。结果表明,水轮机整个叶轮的总体平均受力在剪切流工况中未受到明显影响; 单个叶片的瞬态轴向力系数和瞬态轴向扭矩系数在旋转周期内出现了明显的周期性变化,且周期性变化幅值随转速增大而增大; 非定常的瞬时轴向扭矩和力的周期性振荡容易引起单个叶片的结构性振动,可能对水轮机的机械结构造成影响。     

Enhancement of photoelectrochemical activity of Fe2O3 nanowires decorated with carbon quantum dots

Owing to its up-conversion photoluminescence, photo-induced electron transfer property, and excellent conductivity, carbon quantum dots (CQDs) have been established as effective sensitizers in combination with Fe₂O₃ nanowires for enhancing the catalytic activity of photoelectrochemical water oxidation. In comparison to pristine Fe₂O₃ nanowires, Fe₂O₃ nanowires decorated with CQDs demonstrate 27 orders of magnitude increase in photocurrent density at 0.23 V vs. Ag/AgCl. The mechanism of enhanced photoelectrochemical activity of CQDs/Fe₂O₃ composite was also investigated. Thereby, it is confirmed that the enhanced optical absorption, accelerated interfacial charge carrier transfer and effective separation of photogenerated electron-hole pairs induced by CQDs decoration account for the enhancement of CQDs/Fe₂O₃ nanowire arrays in photoelectrochemical application.     

Gelation properties of goose liver protein recovered by isoelectric solubilisation/precipitation process

Isoelectric solubilisation/precipitation (ISP) process was applied to goose liver (GL) for protein extraction. The gelation properties of proteins extracted by acid processes (ACP, pH 2.0, 2.5 and 3.0) and alkaline processes (ALP, pH 11.0, 11.5 and 12.0) were estimated, where the unextracted ground GL was set as the control. Nearly 58.39~79.00% of GL proteins were recovered by ISP treatments. High molecular weight (100~250 kDa) proteins were found to be partially hydrolysed by ACP, while few changes in proteins occurred during ALP. As evidenced by rheological and textural measurements, ALP proteins formed gels with high elasticity and superior texture, whereas ACP proteins had inferior gelation properties. Moreover, ALP proteins were able to form a highly interconnected and homogeneous three‐dimensional microstructure. Predominantly, gels produced by 11.0 had optimal texture and the lowest cooking loss (P < 0.05). These results suggested that the ISP process (ALP) is a potential method to improve the economic value of GL.     

超临界二氧化碳干气密封稳态性能研究

以超临界二氧化碳(S-CO_2)干气密封为研究对象,建立变黏度变密度雷诺方程,通过构建物性数据库的方式对黏度及密度进行处理,并采用有限差分法对控制方程进行求解,得到端面压力分布,并计算开启力、泄漏量、摩擦扭矩和气膜刚度等稳态性能参数。结果表明:随着压力、转速的增大,开启力、泄漏量、摩擦扭矩、气膜刚度等参数均增大;随着槽坝比和槽深的增加,开启力、泄漏量和气膜刚度均增大,摩擦扭矩减小;随着槽数的增加,各稳态性能参数均减小;将槽坝比控制在0.5～1的范围内,有助于提高密封稳定性。     

泵送剂掺量对充填料浆流动性能及充填体力学性能的影响

泵送剂作为改善充填料浆流动性能的添加剂，已经被广泛应用于矿山，但泵送剂对料浆凝固后充填体力学性能的影响却尚不明确。针对某矿不同泵送剂掺量的充填料浆，开展了料浆塌落度试验、流变试验 、充填体试块单轴抗压强度试验及试块电镜细观试验。结果表明：泵送剂对塌落度呈非线性梯度影响，随着泵送剂掺量不断增加，同剂量的泵送剂对塌落度的影响能力慢慢减弱；屈服应力与塑性黏度均随泵送剂掺量 的增加而降低，泵送剂掺量在超过3%后，屈服应力的下降幅度明显减缓，而对于塑性黏度，掺量超过2%时，其下降幅度就已经开始明显减缓；泵送剂对3 d养护龄期试块强度的影响较弱，而对于7 d、28 d养护龄期试 块，掺量为1%和2%时，对充填体抗压强度的影响是正面的，当掺量大于2%时，充填试块抗压强度呈下降趋势；掺量在1%时充填试块的细观结构是最致密的，随着泵送剂掺量的增加，大孔隙逐渐增加。综合考虑泵送剂 成本、料浆流动性及抗压强度，针对试验中的料浆配比，推荐泵送剂掺量为2%。     

基于硫化铋低温碱性熔炼的熔体物化性质分析

基于硫化铋精矿低温碱性熔炼技术,采用半球点法、旋转柱体法、阿基米德法和拉筒法,测定Bi2S3-NaOH体系的熔化温度、高温密度以及熔体的粘度和表面张力,研究不同NaOH含量和温度对Bi_2S_3-NaOH体系物化性质的影响,结果表明,随着温度的升高,Bi_2S_3-NaOH体系熔化过程分为缓慢收缩,快速收缩和流动阶段,熔化温度随着NaOH含量的增加先减小,达到最低共熔温度后逐渐增大;Bi_2S_3-NaOH熔体的高温密度、表面张力、粘度在NaOH含量一定条件下都随着温度的升高增加而减小,温度一定条件下随着氢氧化钠含量的增加而减小。研究结果可为硫化铋精矿低温清洁冶金技术的优化提供基础数据参考。     

Fabrication and Characterization of Highly Oriented Composite Nanofibers with Excellent Mechanical Strength and Thermal Stability

Here, highly‐oriented poly(m‐phenylene isophthalamide)/polyacrylonitrile multi‐walled carbon nanotube (PMIA/PAN‐MWCNT) composite nanofiber membranes with excellent mechanical strength and thermal stability are successfully produced using electrospinning. It is demonstrated that the cooperation of multi‐walled carbon nanotubes (MWCNT) and high‐speed rotating collection is beneficial to the acquisition of highly oriented fibers and effectively improves the mechanical strength of the membrane along the orientation direction. Specifically, the tensile stress of poly(m‐phenylene isophthalamide)/polyacrylonitrile (PMIA/PAN) membrane is enhanced significantly from 10.6 to 20.7 MPa, benefiting from the highly oriented alignment of the fibers as well as the reinforcing effect of MWCNTs on the fibers. Furthermore, the stressing process of single fiber and fiber aggregates is carefully simulated, and the influence of MWCNTs on the mechanical properties of PMIA/PAN‐MWCNT membranes is analyzed comprehensively, providing a meaningful auxiliary means for the study of mechanical properties. In addition, the composite nanofiber membrane has the advantages of both PMIA and PAN, possessing high temperature resistance, flame‐retardancy, and chemical stability, for an ideal high‐temperature material. In short, the as‐prepared PMIA/PAN‐MWCNT composite membrane with excellent comprehensive property emerges a promising application in many fields, especially in high‐tech.     

碳纤维复合材料修复带缺陷储气井的应力分析及试验研究

针对天然气储气井井管外壁腐蚀现状,采用有限元计算方法,分析不同外壁腐蚀类型、不同腐蚀缺陷尺寸下储气井井管的应力分布、承载极限及疲劳性能;加工带缺陷储气井井管试件,选择碳纤维复合材料湿缠绕法补强修复;对修复后的井管试件进行有限元应力分析,并进行爆破试验和疲劳试验,以充分验证补强方法的有效性;储气井井管的理论分析和性能试验证明,碳纤维复合材料湿缠绕法补强可以有效地修复带外壁缺陷的储气井井管,有效、快捷地解决在役天然气储气井井管外壁腐蚀问题。     

亚磷酸酯功能化聚硅氧烷扩链聚乳酸的阻燃性能研究

将聚氨基环氧基硅氧烷（PSQ）以及亚磷酸酯功能化的聚氨基环氧基硅氧烷（PPSQ）与聚乳酸（PLA）通过熔融共混制备了扩链PLA。研究了亚磷酸酯基团的引入对PSQ在PLA中的扩链和阻燃性能的影响，探究PPSQ在PLA中的阻燃机理。结果表明，相比于PSQ，PPSQ可以明显提高PLA的分子量和复合黏度，具有更好的扩链作用；PPSQ的引入可以明显改善PLA的阻燃性能，使得PLA?PPSQ的极限氧指数提高至25.4 %，比纯PLA提升了31.6 %，且使得PLA的热释放速率峰值和总热释放量分别下降了18.1 %和16.6 %。分析可知，由于亚磷酸酯基团的引入，促使PLA?PPSQ中的硅元素在燃烧过程中向炭层表面迁移形成更多富含碳化硅和氧化硅的致密炭层，起到隔热隔氧的作用，进而发挥优异的阻燃性能。